VESTA 316
Was this helpful?
Was this helpful?
Mobile Lite-R29 Quick Start Guide
1.Package Content
Mobile Lite-R29
Charging & Programming
Regular Micro USB Cable
5V/1A Adaptor
Lanyard
Belt Clip
Cradle (CT-29)
(for charging)
2.Identifying the Parts
Mobile Lite-R29
Front View Side View
Microphone
Active Button
LED (Green/Red)
SIM Card Cover
Fixing Screw
Speaker
SIM Card
SIM Card Slot
Cover
Component
Behavior
Function/Indication
Charging & Programming Cradle (CT-29)
Active Button
Press and hold for 20 seconds
- To turn on the unit (exits airplane mode).
- To turn off the unit (enters airplane mode)
Press once
Trigger emergency alarm
Press and hold for 5 seconds during a
Cancel alarm
Guard Time
Press once when Mobile Lite is ringing
Pick up incoming call
Press and hold for 5 seconds during a
Terminate the call
call
Press and hold for 8 seconds in
Enter RF device learning mode
normal mode
Press twice in learning mode
Remove all learnt device
Press once in learning mode
Exit learning mode
Top LED (Green)
On
Charging
1 flash every 5 seconds
Normal Operation
Top LED (Red)
1 Flash every 3 seconds
Low Battery
When Mobile Lite is charging, the Red LED will not indicate the battery status.
Charging & Programming
Micro USB Jack
Bottom LED (Amber)
1 Flash every 3 seconds
Cellular Network fault
Contact Plates
3.Power Supply
Mobile Lite is powered by rechargeable battery. The typical charging time is 4 hours.
To charge Mobile Lite, please place Mobile Lite into the Charging Cradle, and make sure the Charging Contact Plates (of both Mobile Lite and the cradle) are in contact with each other. Insert the cradle end of Regular Micro USB Cable into the Micro USB Jack and insert the the charging end of the cable into the AC Adapter. Plug the adapter into a power socket.
1
4.Hardware Installation
4.1 SIM Card Insertion
Step 1. Loosen the Cover Fixing Screws using a Philips screwdriver and remove the SIM Card Protective Cover.
Step 2. Insert SIM Card into Mobile Lite, the chip side of the SIM card should face the back side of Mobile Lite as you insert the card.
Step 3. Replace the Protective Cover and tighten the Protective Cover Fixing Screws using a Philips screwdriver.
< NOTE >
Use a SIM card with correct size that can fit in the SIM card slot. If you don’t have the right SIM card size, please contact your service provider for a replacement of SIM card.
Do not insert a SIM card with a SIM card adapter or it will cause damage to the SIM card and its holder.
Please make sure that the SIM card PIN code is deactivated and all SMS messages removed before insertion.
4.2 Lanyard and Belt Clip
Lanyard Attachment
Hook the the lanyard onto the Mobile Lite unit. You’ll hear a click sound when it is hooked well.
Lanyard Removal
Press the button and then push the hook backward to remove the lanyard.
Belt Clip Attachment
Belt Clip Removal
Hook the the belt clip onto the
Press the button to remove the clip.
Mobile Lite unit. Use the clip to
attach the Mobile Lite to the
user’s waistband or belt.
< NOTE >
To effectively trigger the fall detection of Mobile Lite R29, please use the lanyard to wear Mobile Lite on the neck and let it hang in front of the chest instead of using the belt clip which may fail in detecting the user’s falls when he or she wears it on a waistband or puts it inside a coat pocket.
4.3 Installation for Programming
To use PC Programming Tool for programming Mobile Lite, follow the steps below:
Step 1. Place Mobile Lite into the CT-29 Cradle. Make sure the Programming Contact Plates (of both Mobile Lite and the cradle) are in contact with each other.
Step 2. Insert the cradle end of the Programming Micro USB Cable into the Micro USB jack.
Step 3. Insert the programming end of the Programming Micro USB Cable into a computer USB port.
WARNING >
If programming cable is not provided, please contact your supplier. DO NOT attempt to connect Mobile Lite to computer with a Regular Micro USB cable.
Programming Regular
Micro-USB Cable Micro-USB Cable
5.Software Installation
Mobile Lite can be programmed via USB port connection of a computer using
https://www.climax.com.tw/climax-download-mobile-lite-r29.html
the PC Programming Tool software (using the Programming Cable). The USB
Driver must be installed first for your computer to recognize the panel.
● Make sure Mobile Lite is connected properly. (Please refer to 4.3.
Installation for Programming.)
● Go to http://www.ftdichip.com/Drivers/VCP.htm. Select the driver file
according to your operating system, download and install USB driver.
● After installing the driver, unzip the file to a desired folder and execute
the “Mobile_Tool.exe” file.
● For more details about the programming tool, please download
“Mobile Lite R29 Installer Guide” from Climax’s website.
2 2021.11.3
LED (Amber)