VESTA-324
Last updated
Was this helpful?
WTRSC-1
Emergency Pendant/Wrist Transmitter
Easy & Exchangeable Belt / Long battery life / Waterproof
WTRSC-1 is an emergency pendant/wrist transmitter. It is designed to be worn by seniors as they move on the premises, with WTRSC-1, seniors are able to summon help with one simple press.
Active Button
Pressing the Active Button for more than 1 second will activate the Control Panel, causing it to dial emergency call or alarm.
Press and hold the Active Button for 8 seconds to send a Cancel Code to the Control Panel. (This function is not compatible with every control panel).
Battery Life
The Transmitter uses one CR2032 3V Lithium battery as its power source.
Every time the Active Button is pressed, the Wrist Transmitter will check the battery voltage. If low battery status is detected 3 times in a row, the Wrist Transmitter will transmit Low Battery signal along with regular signal every time the button is pressed
Note:
A 30-second interval is required between each Active Button press to check the battery voltage again.
Auto Low Battery Detection
The Wrist Transmitter features Auto Low Battery detection function.
The Wrist Transmitter will automatically check battery voltage every 16-24 hours. If low battery is detected 3 times in a row, the Wrist Transmitter will enter low battery status and transmit low battery signal every 12 hours.
Getting Started
Use a coin to unlock and remove the battery cover from the back of the transmitter by turning the mark on the cover anti-clockwise from Lock position to Open position.
Insert the battery with the unmarked (negative) side facing down.
Use a coin to lock the battery cover back onto the back of the transmitter by turning the mark on the cover clockwise from Open position to Lock position.
Make sure the baseline printed on the back of the transmitter is horizontally aligned with 2 marks of Lock position.
Learn in the Transmitter
Step 1. Put the Control Panel into learning mode.
Step 2. Press the Active Button on the Transmitter. A radio signal will be transmitted to the Control Panel.
Step 3. Please refer to the operation manual of your Control Panel to complete the learning process.
One-Click Lanyard / Wristband Swtich
The Transmitter can be worn as a Pendant with lanyard or a Wrist Watch with wrist band. Please refer to instructions below to switch between wearing a Pendant or as a wrist watch.
2
Step 1. Push the FRONT of the transmitter to take it off from the lanyard frame.
Step 2. Remove the transmitter.
Step 3. Push the transmitter into the wristband frame from the BACK side until you hear a click sound. All done!
Wearing the Transmitter as Wrist Watch
Step 1. Slide the top part of the wristband through the hole at the end of the bottom part of the wristband.
Step 2. Push the protruding part on the inner wristband into right hole for your wrist size.
Compliance with Standards
Complies with the requirements of the Radio Equipment Directive 2014/53/EU Electromagnetic Compatibility Directive 2014/30/EU, Low Voltage Directive 2014/35/EU
Safety:
EMC:
EN 60950-1:2006+A11:2009+A1:2010+A12:2011+A2:2013
EN 50130-4:2011+A1:2014
EN 301489-1:V2.2.0:2017
EN 301489-3:V2.1.1:2017
Radio: EN 300220-1:V3.1.1:2017
EN 300220-2:V1.1.1:2017
EN 300220-3-1:V1.1.1:2017
EN 300220-3-2:V1.1.1:2017
FCC Statement
This device complies with Part 15 of the FCC Rules. Operation is subject to the following two conditions:
This device may not cause harmful interference, and
This device must accept any interference received, including interference that may cause undesired operation.
FCC Caution:
To assure continued compliance, any changes or modifications not expressly approved by the party responsible for compliance may void the user's authority to operate this equipment. (Example - use only shielded interface cables when connecting to computer or peripheral devices).
