# VESTA-193
MOBILE LITE- R3-QT
## VESTA Portable Personal Emergency System
## Mobile Lite R3-QT Quick Start Guide
## **Package Content**
## **Identifying the Parts**
**Charging Cradle**
## **Power Supply**
Mobile Lite is powered by rechargeable battery. The typical charging time is 4 hours. As the battery may not be 100% charged when you get your Mobile Lite, make sure to charge your Mobile Lite before the first use.
To Charge Mobile Lite, please place Mobile Lite into the Charging Cradle, making sure that the Charging Contact Plates (of both Mobile Lite and the cradle) are in contact with each other, and then connect the Charging Cradle to power supply (Refer to ***3.2. Charging Mobile Lite*** of the Mobile Lite Installer Guide).
## **Hardware Installation**
### **SIM Card Insertion**
**Step 1.** Loosen the Cover Fixing Screws using a Philips screwdriver and remove the SIM Card Protective Cover.
**Step 2.** Insert SIM Card into Mobile Lite, the chip side of the SIM card should face the front side of Mobile Lite as you insert the card.
**Step 3.** Replace the Protective Cover and tighten the Protective Cover Fixing Screws using a Philips screwdriver.
{% hint style="warning" %}
Note:
*Use a SIM card with correct size that can fit in the SIM card slot. If you don’t have the right SIM card size, please contact your service provider for a replacement of SIM card.*
*Do not insert a SIM card with a SIM card adapter or it will cause damage to the SIM card and its holder.*
*Please make sure that the SIM card PIN code is deactivated and all SMS messages removed before insertion.*
{% endhint %}
### **Lanyard Attachment**
**Step 1.**
Attach the lanyard to the Mobile Lite unit by looping the lanyard strap through the lanyard holes on the Mobile Lite unit, and then pulling the strap through until it is tight.
**Step 2.**
Lock the release buckle by inserting the male part into the female part until you hear a click sound.
**Step 3.** Put the lanyard around the neck of the user.
### **Installation for Programming**
To use PC Programming Tool for programming Mobile Lite, follow the steps below:
**Step 1.**
Loosen the Protective Cover Fixing Screws using a Philips screwdriver and remove the SIM Card and USB Protective Cover.
**Step 2.**
Insert the device/cradle end of the
Programming Micro-USB Cable into the
Micro-USB jack as shown in the picture:
**Step 3.**
Insert the programming/charging end of the Programming Micro-USB Cable into a computer USB port.
{% hint style="danger" %}
***WARNING***
*If programming cable is not provided, please contact your supplier. DO NOT attempt to connect Mobile Lite to computer with a regular Micro-USB cable.*
{% endhint %}
## **Software Installation**
Mobile Lite can be programmed via USB port connection of a computer using the PC Programming Tool software (using the Programming Cable). The USB Driver must be installed first for your computer to recognize the panel. Please go to to download and install the driver according to your operation system.
* Power on your PC and follow the steps below to install the firmware.
* Enter **** in the address bar.
* Download the PC programming Tool (MobileTool Vx.x).
* For more detailed instruction, please download
“**Mobile Lite R3-QT Installer Guide**” from Climax’s website.
*■ *
---
# Agent Instructions: Querying This Documentation
If you need additional information that is not directly available in this page, you can query the documentation dynamically by asking a question.
Perform an HTTP GET request on the current page URL with the `ask` query parameter:
```
GET https://vesta-guide.gitbook.io/vesta-guide/vesta-193.md?ask=
```
The question should be specific, self-contained, and written in natural language.
The response will contain a direct answer to the question and relevant excerpts and sources from the documentation.
Use this mechanism when the answer is not explicitly present in the current page, you need clarification or additional context, or you want to retrieve related documentation sections.