VESTA 349

VCP-LTE-SV Quick Start Guide

1. Package Content

Voice Call Point A power supply (DC 9V 1A SPS adaptor) A Wall Mounting Bracket

2. Identifying the Parts

▼ Front View ▼ Side View ▼ Back View

LED Indicator (Red) LED Indicator (Green)

Speaker

Microphone

Alarm Button

DC Jack

Battery

Switch

Micro USB Jack Nano SIM Card Slot

Component	Behavior	Condition
Alarm Button	Press once	- To make an emergency call / activate alarm.
		- To answer an incoming call.
	Press and hold for 5 seconds.	- To cancel the alarm.
		- To terminate the call.
	Press and hold for 8 seconds.	- To transmit a learn code to the Control Panel.
LED Indicator (Green)	Light on	AC Power on
	Flashes once every 5 seconds	AC Fail
LED Indicator (Red)	Flashes once every 3 seconds:	Low Battery.
	Flashes once every 5 seconds:	GSM fault.

3. Power Supply

A DC 9V 1A SPS power adapter is provided for AC power connection.

In addition to the AC power adapter, a rechargeable battery is installed inside VCP-LTE-SV to serve as a backup in case of a power failure.

You need to switch the battery switch to ON for the battery to be charged when AC power is connected and serve as a backup power source when AC power is missing.

4. Hardware Installation

Insert SIM card

• It is recommended to disable the SIM card PIN code before inserting into the VCP-LTE-SV.

• The SIM card base is located on the back side of the unit.

• Push to the furthest extend, then press on the edge of the SIM card firmly to secure it.

• SIM Card will delete its SMS messages whenever the VCP-LTE-SV is powered on.

• • Note >

• Only a Nano SIM card can fit in the SIM card slot. If you don’t have the right SIM card size, please contact your service provider for a replacement of SIM card.

• Do not insert a SIM card with a SIM card adapter or it will cause damage to the SIM card and its holder.

1

Wall Mounting

Step 1. Break through the 2 knockouts on the Wall Mounting Bracket.

Step 2. Use the 2 holes as a template to mark off the holes’ positions, making sure that the triangle symbol on the bracket points straight up.

Step 3. Drill 2 holes and screw the bracket onto the wall.

Step 4. Connect a DC 9V 1A SPS power adapter to the DC jack of VCP-LTE-SV and keep the cable well-placed.

ON

ON

Step 5. Fit VCP-LTE-SV onto the mounting bracket. Make sure the imprinted mark on VCP-LTE-SV is aligned with the upper mark on the bracket.

Step 6. Rotate VCP-LTE-SV clockwise to the lock position.

Open position

Lock position

Surface Placement

Step 1. Clean the back of VCP-LTE-SV with degreaser. Connect a DC 9V 1A SPS power adapter to the DC jack and keep the cable well-placed to the right or left.

Step 2. Remove the protective cover of Anti-Slip pad and apply to the back of VCP-LTE-SV.

Step 3. Place VCP-LTE-SV at the desired location.

5. Software Installation

VCP-LTE-SV can be programmed via USB port connection of a computer using the PC Programming Tool software (with the Programming Cable). The USB Driver must be installed first for your computer to recognize the USB connection. Please go to http://www.ftdichip.com/Drivers/VCP.htm to download and install the driver according to your operation system.

• Power on your PC and follow the steps below to install the firmware.

• Enter https://www.climax.com.tw/climax-download-vcp-lte-sv.html in the address bar.

• Download the PC programming Tool (MobileTool).

• For more detailed instruction, please download “ VCP-LTE-SV Voice Call Point Installation Guide ”.

  • https://www.climax.com.tw/climax-download-vcp-lte-sv.html

2 2023-03-15