DANALOCK WITH VESTA (Z-WAVE)

Introduction

Welcome to the installation and setup manual for SALTO locks, models SALTO-015 and SALTO-17. This document will guide you step by step through the process of installing, adding, and calibrating these locks with a VESTA panel using Z-WAVE technology.

SALTO-017

SALTO-017

SALTO-15

SALTO-005

SALTO locks provide an advanced and secure access control solution, and by integrating them with the VESTA panel, you can efficiently manage and monitor access in real-time. This manual is designed to make the installation process easy, ensuring you can quickly take advantage of all the benefits that this integration offers.

Guidelines

Prerequisites

• Ensure that the VESTA panel has Z-WAVE check the Vesta WEB for the specifications of your control panel:

If your control panel do not have Z-WAVE you can install a VESTA-240 module.

• Check that your cylinder is double clutch: This means that if you insert the key from the outside, you can still open and close it from the inside.

If you have a double clutch cylinder and you want to keep your keys, you need the SALTO-005 adapter.

Manual Guide to install key adapter

Installation Steps

Lock Mounting

Z-WAVE Connection: Procedure for adding the lock to the VESTA panel via Z-WAVE.

Once the installation is complete and the batteries are installed, we are going to proceed with the registration in VESTA. After you have physically installed the SALTO lock and inserted the batteries, the next step is to register the lock with the VESTA panel. This registration process is necessary to link the lock to the VESTA system so that it can be managed and controlled through the panel.

This exclude option is very important to be able to leave the device without information and registration data, so that it can be correctly added to the VESTA coordinator. Before adding the lock to the VESTA system, it’s crucial to perform an “exclude” operation. Excluding the device ensures that any previous connection data or registration information stored on the lock is erased. This step essentially resets the lock, removing any old network data, so it’s ready to be correctly added (or "included") to the VESTA coordinator (the central Z-WAVE hub). If you skip this step, the lock might have leftover data that could interfere with the new registration process, leading to connection issues.

Exclude Z-WAVE DANALOCK

Step 1: Access the panel configuration from the installer APP:

Installer -> Settings

Step 2: Select "Devices" in the menu.

Installer -> Settings -> Devices

Step 3: In the menu click "Exclude device".

Select EXCLUDE

Step 4. Now click once on the lock button.

Press button 1 time for Inclusion/exclusion

Once the lock button has been pressed only once, Danalock led is green blinking, and the panel is in exclusion mode, wait for 1 minute. In the SmartHomeSec APP a question "?" mark may appear in the exclusion box, this is normal. once it appears close the exclusion window.

Add Z-WAVE DANALOCK in VESTA

It is crucial to have made the exclusion before

Step 1: In device list of SmartHomeSec, choose Add device:

Step 2. Now click once on the lock button.

Press button 1 time for Inclusion/exclusion

Once the lock button has been pressed only once, Danalock led is green blinking, and the panel is in adding mode, wait for 1 minute. In the SmartHomeSec APP you will see the doorlock, add It and you can control it from automations 🎉

Calibration

To calibrate your Danalock, follow these steps carefully:

• Set the Danalock to the Unlocked Position: Turn the Danalock to the unlocked position. If necessary, lift the handle.

• Start Calibration: Click the button on the Danalock 3 times. The lock will automatically calibrate and stop in the locked position.

Auto-Calibration

• Adjust to the Unlocked Position: Turn the Danalock to the position where it is just unlocked (not further). Click the button on the Danalock once.

• Adjust to the Locked Position: Turn the Danalock to the position where it is just locked (not further). Click the button on the Danalock once.

🎉 Congratulations! Your lock is installed and ready to control your door automatically.

Extra information

Danalock V3 click commands

How to change battery?