VESTA-193

Mobile Lite R3-QT Quick Start Guide

1.Package Content

5V/1A Adaptor

Mobile Lite R3-QT Charging Cradle or Micro-USB cable Lanyard 5V/2A AU Plug Adaptor

2.Identifying the Parts

Mobile Lite

Active Button

Microphone

LED (Green/Red)

LED (Amber)

Speaker

SIM Card Cover

Fixing Screw

SIM Card and

USB Cover

Micro SIM

Card Slot

Micro USB Jack

Component	Behavior		Function/Indication
			Press and hold for 5 seconds	- To turn on the unit (exits sleep mode)
				- To turn off the unit (enters sleep mode). Cellular module will be
							powered down 30 seconds after the button is pressed for 5 seconds.
			Press once	Trigger emergency alarm
			Press and hold for 5 seconds during Guard Time	Cancel alarm
Active Button	Press once when Mobile Lite is ringing	Pick up incoming call
Press and hold for 5 seconds during a call	Terminate the call
			Press and hold for 8 seconds in normal mode	Enter RF device learning mode
			Press twice in learning mode	Remove all learnt devices
			Press once in learning mode	Exit learning mode
	Top LED (Green)			On			Charging
			1 Flash every 5 seconds			Normal Operation
Top LED (Red)		1 Flash every 3 seconds	Low Battery
When Mobile Lite is charging, the Red LED will not indicate the battery status.
	Bottom LED (Amber)			1 Flash every 3 seconds			Cellular Network fault

Charging Cradle

Cradle Charging

Contact Plates

Cradle USB Jack

1

3.Power Supply

Mobile Lite is powered by rechargeable battery. The typical charging time is 4 hours. As the battery may not be 100% charged when you get your Mobile Lite, make sure to charge your Mobile Lite before the first use.

To Charge Mobile Lite, please place Mobile Lite into the Charging Cradle, making sure that the Charging Contact Plates (of both Mobile Lite and the cradle) are in contact with each other, and then connect the Charging Cradle to power supply (Refer to 3.2. Charging Mobile Lite of the Mobile Lite Installer Guide).

4.Hardware Installation

4.1 SIM Card Insertion

Step 1. Loosen the Cover Fixing Screws using a Philips screwdriver and remove the SIM Card Protective Cover.

Step 2. Insert SIM Card into Mobile Lite, the chip side of the SIM card should face the front side of Mobile Lite as you insert the card.

Step 3. Replace the Protective Cover and tighten the Protective Cover Fixing Screws using a Philips screwdriver.

< NOTE >

• Use a SIM card with correct size that can fit in the SIM card slot. If you don’t have the right SIM card size, please contact your service provider for a replacement of SIM card.

• Do not insert a SIM card with a SIM card adapter or it will cause damage to the SIM card and its holder.

• Please make sure that the SIM card PIN code is deactivated and all SMS messages removed before insertion.

4.2 Lanyard Attachment

Step 1.

Attach the lanyard to the Mobile Lite unit by looping the lanyard strap through the lanyard holes on the Mobile Lite unit, and then pulling the strap through until it is tight.

Step 2.

Lock the release buckle by inserting the male part into the female part until you hear a click sound.

Step 3. Put the lanyard around the neck of the user.

4.3 Installation for Programming

To use PC Programming Tool for programming Mobile Lite, follow the steps below:

Step 1.

Loosen the Protective Cover Fixing Screws using a Philips screwdriver and remove the SIM Card and USB Protective Cover.

Step 2.

Insert the device/cradle end of the

Programming Micro-USB Cable into the

Micro-USB jack as shown in the picture:

Step 3.

Insert the programming/charging end of the Programming Micro-USB Cable into a computer USB port.

< WARNING>

• If programming cable is not provided, please contact your supplier. DO NOT attempt to connect Mobile Lite to computer with a regular Micro-USB cable.

Programming Regular

Micro-USB Cable Micro-USB Cable

5.Software Installation

Mobile Lite can be programmed via USB port connection of a computer using the PC Programming Tool software (using the Programming Cable). The USB Driver must be installed first for your computer to recognize the panel. Please go to http://www.ftdichip.com/Drivers/VCP.htm to download and install the driver according to your operation system.

• Power on your PC and follow the steps below to install the firmware.

• Enter https://www.climax.com.tw/climax-download-mobile-lite-r3-qt.html in the address bar.

• Download the PC programming Tool (MobileTool Vx.x).

• For more detailed instruction, please download

“Mobile Lite R3-QT Installer Guide” from Climax’s website.

■ https://www.climax.com.tw/climax-download-mobile-lite-r3-qt.html

2020.05.27

2