VESTA 173

RSB-1ZBS

RGBW Smart Bulb

Introduction

The RSB-1ZBS is a ZigBee Smart LED Color Light Bulb. It features both multicolor adjustment and light level control. When joined into a ZigBee network, the user will be able to control Light Bulb remotely from the ZigBee network coordinator.

The Light Bulb utilizes ZigBee technology for wireless signal transmission. ZigBee is a wireless communication protocol that is reliable and has low power consumption and high transmission efficiency. Based on the IEEE802.15.4 standard, ZigBee allows a large amount of devices to be included in a network and coordinated for data exchange and signal transmission

The Light Bulb also serves as a route in the ZigBee network. After being included in the ZigBee network, it allows other ZigBee devices to join the network through the Light Bulb.

ZigBee Network Setup

• ZigBee Device Guideline

ZigBee is a wireless communication protocol that is reliable, has low power consumption and has high transmission efficiency. Based on the IEEE802.15.4 standard, ZigBee allows a large amount of devices to be included in a network and coordinated for data exchange and signal transmission.

Due to the fundamental structure of ZigBee network, ZigBee device will actively seek and join network after powering on.

• • Ensure your ZigBee network router or coordinator is powered on before powering on the ZigBee device.

  • Ensure your ZigBee network router or coordinator is powered on and within range while a ZigBee device is in use.

  • Do not remove a ZigBee device from the ZigBee network router or coordinator without powering down the ZigBee device.

• Joining the ZigBee Network

As a ZigBee device, the Light Bulb needs to join a ZigBee network to send and receive command signals. Please follow the steps below to add the Light Bulb into the ZigBee network.

Step 1. Scroll the Light Bulb into the lamp socket. Do not supply power yet.

Step 2. Enable the permit-join feature on the router or coordinator of your ZigBee network.

Step 3. Switch ON Light Bulb for 3~5 seconds. (No more than 5 seconds), then switch OFF.

Step 4. Repeat Step 3 for three (3) times for a total of four (4) ON/OFF cycles.

Step 5. Switch ON Light Bulb for the 5th time, the device will reset and start searching for new ZigBee network.

Step 6. After joining the ZigBee network, the Light Bulb will be registered in the security system in the network automatically. Please check the ZigBee network coordinator, system control panel, or CIE (Control and Indicating Equipment) to confirm if joining and registration was successful.

• Removing Device from ZigBee Network (Factory Reset)

To remove the Light Bulb from current ZigBee network, the device must be placed on Factory Reset to complete device removal. Factory Reset function will clear the Light Bulb of its stored setting and information and prompt the Light Bulb to search for new ZigBee network.

Before removing device, make sure the Light Bulb is within current ZigBee network signal range

1. Delete the Light Bulb from current control panel / CIE.

2. Power off the Light Bulb.

3. Switch ON Light Bulb for 3~5 seconds. (No more than 5 seconds), then switch OFF.

4. Repeat Step 3 for 3 times for a total of 4 ON/OFF cycles

5. Switch ON Light Bulb for the 5th time, the device will reset and start searching for new ZigBee network.

6. Upon reset, the Light Bulb will clear current ZigBee network setting and transmit signal to ZigBee coordinator to remove itself from current ZigBee network. It will then actively search for available ZigBee network again and join the network automatically.

1

• ZigBee Router Device Capacity

The Light Bulb with Router function allows other ZigBee devices to join the ZigBee Network through the Router. The Light Bulb has a maximum capacity of 7 devices, including 4 routers.

Features

• Color and Saturation Adjustment

The Light Bulb’s color and saturation may be adjusted from the ZigBee Coordinators remotely by sending commands.

• Light Level Adjustment

The Light Bulb has dimmable lighting, the light percentage maybe adjusted from the ZigBee Coordinators remotely by sending commands.

• Supervision

The Light Bulb will transmit a supervision signal to report its condition regularly according to user setting. The factory default interval is 10 minutes.

Appendix (For developers only)

• Light Bulb Cluster ID

Device ID: Color_Dimmable_Light: 0x0102

Endpoint: 0x01

Server Side			Client Side
		Mandatory
Basic (0x0000)				None
Identify(0x0003)
Groups(0x0004)
Scenes(0x0005)
OnOff(0x0006)
Level Control(0x0008)
Color Control(0x0300)
		Optional
None				None
Report Cluster		On/Off (0x0006)
Report Attribute		ATTRID_ON_OFF (0x0000)
Datatype		ZCL_DATATYPE_BOOLEAN
minReportInt		0
maxReportInt		default value: 0x258 sec (600 sec)
Report Cluster		Level Control (0x0008)
Report Attribute		ATTRID_LEVEL_CURRENT_LEVEL (0x0000)
Datatype		ZCL_DATATYPE_UINT8
minReportInt		0
maxReportInt		default value: 0x258 sec (600 sec)
Report Cluster		Color Control (0x0300)
Report Attribute		ATTRID_LIGHTING_COLOR_CONTROL_CURRENT_HUE (0x0000)
Datatype		ZCL_DATATYPE_UINT8
	ATTRID_LIGHTING_COLOR_CONTROL_CURRENT_SATURATION (0x0001)
Datatype		ZCL_DATATYPE_UINT8
	ATTRID_LIGHTING_COLOR_CONTROL_COLOR_TEMPERATURE (0x0007)
Datatype		ZCL_DATATYPE_UINT16
minReportInt		0
maxReportInt		default value:0x258 sec (600 sec)
		2

• Attribute of Basic Cluster Information

Identifier	Name	Type	Range	Access	Default	Mandatory
/ Optional
0x0000	ZCLVersion	Unsigned 8-bit	0x00 –0xff	Read only	0x01	M
integer
0x0003	HWVersion	Unsigned 8-bit	0x00 –0xff	Read only	0	O
integer
0x0004	ManufacturerName	Character	0 – 32 bytes	Read only	Climax Technology	O
String
0x0005	ModelIdentifier	Character	0 – 32 bytes	Read only	SLCB_00.00.03.01	O
String	TC
0x0006	DateCode	Character	0 – 16 bytes	Read only	20170124	O
String
0x0007	PowerSource	8-bit	0x00 –0xff	Read only		M
Enumeration
0x0010	LocationDescription	Character	0 – 32 bytes	Read/Write		O
string
0x0011	PhysicalEnvironment	8-bit	0x00 –0xff	Read/Write	0x00	O
Enumeration
0x0012	DeviceEnabled	Boolean	0x00 –0x01	Read/Write	0x01	M
 Attribute of Identify Cluster Information

Identifier	Name	Type	Range	Access	Default	Mandatory /
Optional
0x0000	IdentifyTime	Unsigned	0x00 –0xffff	Read / Write	0x0000	M
16-bit integer
 Attribute of Group Cluster Information

Identifier	Name					Type				Range			Access			Default	Mandatory /
												Optional
0x0000	NameSupport				8-bit bitmap			X0000000		Read only				-		M
 Attribute of Scenes Cluster Information
Identifier	Name					Type				Range			Access		Default		Mandatory
											/ Optional
0x0000	SceneCount		Unsigned 8-bit integer		0x00 – 0xff			Read only		0x00		M
0x0001	CurrentScene		Unsigned 8-bit integer		0x00 – 0xff			Read only		0x00		M
0x0002	CurrentGroup	Unsigned 16-bit integer		0x0000 – 0xfff7		Read only		0x00		M
0x0003	SceneValid					Boolean				0x00 – 0x01			Read only		0x00		M
0x0004	NameSupport					8-bit bitmap				X0000000			Read only		-		M
 Attribute of On/Off Cluster Information
Identifier	Name					Type					Range				Access		Default	Mandatory /
													Optional
0x0000	OnOff					Boolean			0x00 – 0x01			Read Only		0x00		M
 Attribute of Level Control Cluster Information
Identifier	Name					Type				Range			Access		Default		Mandatory
											/ Optional
0x0000	CurrentLevel		Unsigned 8-bit integer		0x00 – 0xff			Read only		0x00		M
 Attribute of Color Control Cluster Information
Identifier	Name					Type				Range				Access		Default		Mandatory
												/ Optional
0x0000	CurrentHue					Unsigned				0x00 – 0xff				Read only			0x00		M
				8-bit integer
0x0001	CurrentSaturation				Unsigned				0x00 – 0xfe				Read only			0x00		M
			8-bit integer
0x0007	ColorTemperatureMireds		Unsigned				0x0000 –				Read only	0x00fa (4000K)		M
	16-bit integer				0xfeff
0x0008	ColorMode					8-bit			0x00 – 0x02		Read only			0x01		M
				enumeration

3