VESTA-481
PSS-29-R2-ZW
Power Switch
Introduction
The Z-Wave-enabled Power Switches are capable of receiving wireless signals from the coordinator in the Z-Wave network to toggle On/Off of appliances that are attached to it. The Power Switch also serves as a router in the Z-Wave network. After being included in the Z-Wave network, it allows other Z-Wave device to join the network through the Power Switch.
Z-Wave is a wireless communication protocol that uses a low-power RF radio. By taking advantage of the Z-Wave mesh network, commands can be transmitted to their destination via intermediary “listening” Z-Wave products.
The Z-Wave Power Switches allow access to the “S2 Unauthenticated” class and support Z-Wave SmartStart inclusion as well as classic inclusion.
Parts Identification
1. Function Button aka LED indicator
The Function Button also doubles as the LED Indicator. The Function Button is used to control the Power Switch. The LED indicator is used to indicate Power Switch status.
LED Indication:
The LED indicator lights up in the following conditions:
On: power on
Off: power off
Red light flashes twice:
The Power Switch has just been powered on.
The Power Switch has just been factory reset.
Function Button Usage:
Press the Function Button to switch on/off the Power Switch.
Press the Function Button 3 times within 1.5 seconds to transmit a learn code.
Press and hold the Function Button for 10 seconds to factory reset.
Features
Adding Device (Inclusion)
This product can be included and operated in any Z-Wave network with other Z-Wave certified devices from other manufactures and/or other applications. All non-battery-operated nodes within the network will act as repeaters regardless of vendor to increase reliability of the network.
The device supports both classic inclusion process and SmartStart inclusion process.
Classic Inclusion
If the device has already been added (included) into another Z-Wave Gateway/Control Panel, or if the device is unable to be added into the current Z-Wave Gateway/Control Panel, please exclude it first (see Removing Device) before attempting to include it into the current Z-Wave Gateway/Control Panel.
SmartStart Inclusion
Z-Wave SmartStart utilizes the DSK of the device to enhance and simplify the inclusion process. DSK is Device Specific Key used for authentication. The DSK information is stored in the QR code format that is printed on a sticker and attached to the device.
Removing Device (Exclusion)
The device must be removed from existing Z-Wave network before being included into another. There are two methods available to exclude a device.
Exclusion Mode
Factory Reset
Only use factory reset when network Control Panel/Gateway is missing or inoperable.
Press and hold the Function Button of the device for 10 seconds to factory reset.
Range Test
To test whether the device is able to communicate with the Z-Wave Gateway or Control Panel:
Z-Wave Router Device Capacity
The Power Switch allows other Z-Wave devices to join the Z-Wave Network through the Router. The maximum capacity of the devices to join the Z-Wave Network through the Power Switch is 255.
Operation
Appliance Control
After being included into a Z-Wave Gateway or Control Panel, plug a home appliance into the Power Switch. This home appliance’s power and energy usage data will be transferred to the Control Panel.
Users can remotely turn on/off the electric appliance through the Control Panel (please refer your Control Panel manual).
Pressing the Function Button on the Power Switch can also toggle on/off the Power Switch.
The Power Switch transmits a signal with power data to Z-Wave Gateway/Panel every 10 minutes starting from the last time a signal is transmitted.
When the Power Switch is re-plugged after it has been removed from the power outlet, the previous on/off status of Power Switch will be resumed immediately.
Power Specification
For 110V: the maximum operation load is 1760W and 16A. Warning: please do not exceed the maximum load.
For 230V: the maximum operation load is 3680W and 16A. Warning: please do not exceed the maximum load.
If the Power Switch is overheating, it will cut off power automatically as a safety measure. The Power Switch must be un-plugged and re-plugged after cut off to resume normal operation.
Z-Wave Information
Device Type: On/Off Power Switch
Role Type: Always On Slave (AOS)
Command Class Support/Control
Mandatory CC Support:
Association CC, v2 or newer
Association Group Information CC
Basic CC
Binary Switch CC
Device Reset Locally CC
Manufacturer Specific CC
Powerlevel CC
Version CC, v2 or newer
Z-Wave Plus Info CC
Recommended CC Support:
Firmware Update Metadata CC
Z-Wave’s Groups (Association Command Class Version 2)
The Switch can be set to send reports to associated Z-Wave devices. It supports one association group with five node support for Grouping 1. For grouping 1, the Switch will report its latest status to Z-Wave Gateway/Panel. Grouping 1 includes:
Binary Switch CC (SWITCH_BINARY_REPORT)
Device Reset Locally CC (COMMAND_CLASS_DEVICE_RESET_LOCALLY)
Auto report to Grouping 1 (Maximum Node 5)
On/Off Event Report
When toggling between On/Off, it will send Binary Switch Report to the nodes of Grouping 1.
Factory Reset
When the Power Switch is reset to factory default, it will send Device Reset Locally to all nodes in Group 1.
Last updated